Dovient

How-to

Warehouse maintenance checklist (conveyors, doors, lighting)

A warehouse maintenance checklist covering conveyor maintenance, dock and overhead doors, and lighting, with a schedule by shift, week, month and year.

Where warehouse maintenance goes wrong

In most warehouses the work that gets skipped is the work nobody owns: belt conveyors that run until a bearing seizes, overhead doors that slam because a spring is broken, and burned-out fixtures in the high bays that nobody wants to climb to. Each one turns into a stopped shipping lane, an injury risk or an emergency call.

The fix is a written schedule with an owner for each item, and a record of each check. Take intervals from the manufacturers' manuals and adjust them with your own breakdown history.

Conveyor maintenance

Lock out the conveyor before clearing a jam or working inside the guards. OSHA's lockout/tagout standard (29 CFR 1910.147) applies to servicing and maintenance where an unexpected start-up could hurt someone, and its machine guarding rule (1910.212) covers exposed nip points and moving parts. ASME B20.1 is the industry safety standard for conveyors.

  • Each shift: walk the line with it running; listen for noisy bearings and rollers, look for belt tracking problems, check that emergency stops and pull cords are reachable.
  • Weekly: clean debris from under the conveyor and around tail pulleys; check belt tension and splices; check that guards are in place over chains, sprockets and nip points.
  • Monthly: lubricate bearings and chains per the manual; check gear reducer oil level; check motor mounts and electrical connections for heat or looseness; test every emergency stop.
  • Yearly: inspect pulleys, lagging, rollers and drive components; replace worn belts and reducer oil on the manufacturer's interval.

Doors, lighting and the building

  • Overhead and high-speed doors: check daily that safety edges and photo eyes stop the door; monthly check springs, cables, rollers and tracks; yearly service by a qualified door company.
  • Lighting: walk the building monthly and log fixtures out; test emergency lights and exit signs monthly; plan group relamping in high bays rather than one fixture at a time.
  • Roof and drains: inspect roof drains and gutters before and after the wet season, and after storms.
  • HVAC and heaters: replace filters on schedule; service unit heaters and rooftop units before the heating and cooling seasons.
  • Floors: log cracks and potholes in forklift aisles; repair before they damage wheels and loads.

Warehouse monthly maintenance

Monthly, by area

Conveyors

  • Belts tracking straight, splices intact
  • No noisy bearings or seized rollers
  • Guards in place over chains and nip points
  • Emergency stops and pull cords stop the line
  • Reducer oil at the correct level

Doors

  • Doors open and close without binding
  • Safety edge or photo eye reverses the door
  • Springs, cables and rollers intact

Lighting and exits

  • All fixtures in aisles and docks working
  • Emergency lights work on test
  • Exit signs lit, exit routes clear

Building

  • Roof drains and gutters clear
  • Aisle floors smooth, no potholes
  • HVAC and heater filters changed on schedule

Inspected by, date and notes go at the bottom of the printed sheet.

Run it in Dovient Lite

Add each conveyor section, door and rooftop unit as an asset with its location, and set preventive schedules by date or by motor hours with this checklist attached. A work order opens when each is due, the tech marks items pass, warning or fail on the phone, and the record stays on the asset. Staff report a jammed conveyor or broken door from the phone and can mark it a breakdown, and the dashboard shows downtime and repeat failures by asset.

Start with Dovient Lite

Sources

Rules change and vary by state and county. Check the current text with your inspector or authority having jurisdiction. Last reviewed 2026-11-15.

Questions

How often should conveyors be maintained?
Walk them each shift, clean and check belts and guards weekly, lubricate and test emergency stops monthly, and do a full inspection yearly. Follow the manufacturer's intervals for lubrication and belt replacement.
What should a warehouse maintenance checklist include?
Conveyors, dock and overhead doors, lighting and emergency lights, roof drains, HVAC and heaters, and floor condition, each with a set interval and an owner.
Does lockout/tagout apply to clearing conveyor jams?
Generally yes, when the work exposes someone to an unexpected start-up. OSHA's 1910.147 has a narrow exception for minor servicing done with other effective protection.