Dovient

Template

Warehouse safety & OSHA inspection checklist

A monthly warehouse safety checklist mapped to the OSHA warehouse regulations an inspector cites most: aisles and floors, storage, exits, forklifts, electrical, chemicals and docks.

Which OSHA rules apply to a warehouse

OSHA has no single warehouse standard. Warehouses fall under the general industry rules in 29 CFR 1910, and OSHA's warehousing page lists the ones that matter most. The checklist below follows them.

  • Walking-working surfaces, 1910.22: floors kept clean and dry where feasible, surfaces inspected regularly and hazards fixed before use. Dock edges and fall protection are in Subpart D.
  • Materials handling and storage, 1910.176: aisles kept clear and in good repair, and stored material stacked so it is stable and secure.
  • Exit routes, 1910.36 and 1910.37: exit routes kept clear of materials and equipment, lit, and marked with Exit signs; exit doors open from the inside without a key.
  • Powered industrial trucks, 1910.178: daily truck examinations, operator training and safe battery charging areas.
  • Portable fire extinguishers, 1910.157; electrical, 1910.303 to 1910.308; first aid and eyewash where corrosives are handled, 1910.151; hazard communication, 1910.1200; lockout/tagout for maintenance, 1910.147.

How often to inspect

  • Before each shift: forklift pre-shift checks by the operators.
  • Weekly: a supervisor walk of aisles, exits and docks.
  • Monthly: this full checklist, plus fire extinguisher monthly checks.
  • Yearly: extinguisher service, emergency lighting full test, racking review by a qualified inspector, and a review of your hazard communication and lockout programs.

What records to keep and what an inspector looks at

Keep the signed checklists, the work orders that fixed what they found, forklift daily checks, operator training and evaluation records, extinguisher maintenance records, and your written hazard communication program with current safety data sheets.

An OSHA compliance officer walks the floor first. Blocked exits and aisles, damaged racking, forklifts running with defects, missing safety data sheets or labels, and blocked electrical panels are the common findings. Records then show whether a problem was a one-off or a pattern.

How to run the inspection

  1. Walk the building in the same order each time: docks, aisles and racking, charging area, exits, electrical rooms, chemical storage.
  2. Mark each item and photograph anything that fails, with its aisle or door number.
  3. Fix what you can on the spot, such as clearing an exit, and assign the rest with a due date.
  4. Unload and tag damaged rack bays until they are repaired.

Warehouse safety inspection

Monthly, for each building

Floors, aisles and docks

  • Aisles clear, marked and in good repair
  • Floors clean and dry, no holes or spills
  • Dock edges marked, plates and levelers working
  • Wheel chocks or restraints used at docks

Storage and racking

  • Loads stacked stable and within height limits
  • Rack uprights and beams not bent or damaged
  • Beam locks in place, load signs posted
  • No storage within 18 inches of sprinkler heads

Exits and fire

  • Exit routes clear and unobstructed
  • Exit signs lit, exit doors open from inside
  • Extinguishers in place and inspected
  • Emergency lights work on test

Forklifts and charging

  • Daily truck checks done and signed
  • Charging area ventilated, no smoking signs
  • Eyewash at charging area works and is clean
  • Damaged trucks tagged out of service

Electrical and chemicals

  • Electrical panels clear, covers closed
  • No damaged cords or daisy-chained power strips
  • Containers labeled, safety data sheets on hand
  • First aid kit stocked

Inspected by, date and notes go at the bottom of the printed sheet.

Run it in Dovient Lite

Add each building area, dock door and rack aisle as an asset with its location, and set a monthly schedule with this checklist attached. The supervisor walks the floor, marks each item pass, warning or fail on the phone with photos, and the inspection is saved with who did it and when. Each problem found becomes a work order the supervisor assigns, and completed inspections and repairs export as PDF when an inspector or insurer asks.

Start with Dovient Lite

Sources

Rules change and vary by state and county. Check the current text with your inspector or authority having jurisdiction. Last reviewed 2026-11-15.

Questions

What are the OSHA requirements for a warehouse?
Warehouses follow the general industry rules in 29 CFR 1910, mainly walking-working surfaces, materials storage, exit routes, forklifts, fire extinguishers, electrical, hazard communication and lockout/tagout.
How often should a warehouse safety inspection be done?
OSHA requires walking-working surfaces to be inspected regularly and as necessary, and forklifts daily. Most warehouses do a supervisor walk weekly and a full documented inspection monthly.
What are the most common OSHA warehouse violations?
OSHA notes warehouses are frequently cited under hazard communication. Forklift, exit route, walking-working surface and electrical findings are also common in warehouse inspections.
Does OSHA require a written warehouse inspection checklist?
Most of these rules require the condition, not a form. A signed checklist with the repairs that followed is how you show an inspector that you find and fix hazards.