What OSHA and the rack standard say
OSHA has no standard written only for pallet racking. The rule that applies is 29 CFR 1910.176(b): storage must not create a hazard, and stored material must be stable and secure against sliding or collapse. 1910.176(a) also requires aisles kept clear and in good repair where forklifts run. A damaged rack that could collapse can also be cited under the General Duty Clause, section 5(a)(1) of the OSH Act, which requires employers to keep the workplace clear of recognized serious hazards.
The industry standard for steel pallet racks is ANSI MH16.1, published by the Rack Manufacturers Institute (RMI). It covers how racks are designed and rated. For your own racks, the rack maker's load ratings and repair instructions are what to follow: a repaired upright should use the maker's parts or an engineered repair, never a welded patch done in house.
How often to inspect pallet racking
No federal rule sets a fixed interval, so set one by how busy the aisles are. A schedule many warehouses use:
- Every shift: forklift operators report any hit or damage they see or cause.
- Monthly: a supervisor walks every aisle with the checklist below and records the result.
- Once a year: a full inspection by a qualified person, such as a rack engineer or the rack maker's inspector.
- Right away: after any forklift impact, overload, move or reconfiguration of the racks.
What to do when you find damage
- Unload the bay and the bays next to it if an upright is bent, torn or missing anchors.
- Tag or tape off the bay so no one loads it.
- Photograph the damage and note the aisle, bay and level.
- Get the repair or replacement from the rack maker or an engineered repair kit.
- Record the repair and put the bay back in service only after it is done.
Records to keep
Keep each monthly walk, each annual inspection report and each repair, with the date, the location in the rack and who did it. If an OSHA inspector asks about a damaged upright, a record that shows when it was found, when the bay was unloaded and when it was fixed is your best answer.
Pallet racking inspection
Monthly, and after any impact
Uprights and base
- Uprights straight, not bent, torn or twisted
- Base plates flat and anchored to the floor
- Anchor bolts present and tight
- Column guards and end protectors in place
Beams and connections
- Beams level, not bent or sagging
- Beam locks or safety pins in every connector
- Beam connectors not cracked or deformed
- Bracing between uprights intact and tight
Loads
- Loads within the posted capacity
- Pallets sound and sitting square on beams
- No loads hanging over the beams or flue space
- Wire decking or pallet supports in place
Signs and aisles
- Load capacity signs posted and legible
- Aisles clear and marked
- Rack-to-wall and row spacers in place
Inspected by, date and notes go at the bottom of the printed sheet.
Run it in Dovient Lite
Add each rack row or aisle as an asset with its location and print a QR label for the end of each row. Set a monthly schedule with this checklist attached; a work order opens when it is due, and the supervisor marks each item on the phone with a photo of any damage. Operators who hit a rack report it from the phone with a photo, which becomes a repair work order, and the full history stays on that row's record.
Start with Dovient LiteSources
- OSHA, Handling materials, general, 29 CFR 1910.176(a) and (b)
- OSH Act, General Duty Clause, Section 5(a)(1)
- Rack Manufacturers Institute, ANSI MH16.1 specification for industrial steel storage racks
Rules change and vary by state and county. Check the current text with your inspector or authority having jurisdiction. Last reviewed 2026-11-15.
Questions
- Does OSHA require pallet rack inspections?
- OSHA has no rack-specific inspection interval, but 1910.176(b) requires storage to be stable and secure, and damaged racks can be cited under the General Duty Clause. Regular documented inspections are how you show the racks are safe.
- How often should pallet racking be inspected?
- A common schedule is operator reports every shift, a documented supervisor walk monthly, and a full inspection by a qualified person once a year. Inspect right away after any impact.
- Can a bent rack upright be straightened?
- No. A bent upright should be unloaded and replaced or repaired with the rack maker's parts or an engineered repair kit.
- What records do I need for rack inspections?
- Keep each inspection with the date, who did it and what was found, and each repair with where it was and when it was finished.