What the rules expect of maintenance
FDA's current good manufacturing practice rules for human food, in 21 CFR Part 117 Subpart B, set the maintenance baseline for most US food plants. Buildings, fixtures and facilities must be kept clean and in repair adequate to keep food from becoming adulterated (117.35(a)). Equipment must be cleanable, adequately maintained, and used so lubricants, fuel, metal fragments and contaminated water do not get into food (117.40(a)). Instruments that measure or control temperature, pH, acidity or water activity must be accurate, precise and adequately maintained (117.40(f)), and freezers and cold storage need a working thermometer or recorder (117.40(e)).
Plants covered by the preventive controls rules also have to verify their controls, which often includes calibrating monitoring instruments. GFSI audit schemes such as SQF and BRCGS add written requirements for a maintenance program, food-grade lubricants and hygienic clearance after repairs.
How to build the program
- List every piece of equipment and utility: fillers, mixers, ovens, fryers, slicers, conveyors, metal detectors, compressors, boilers, refrigeration and HVAC.
- Rank each one by food safety risk and by how much production stops when it fails.
- Set tasks and intervals from the manuals: by date for inspections and calibrations, by run hours for lubrication, belts and wear parts.
- Write a checklist for each recurring task, including the food safety steps: lockout, food-grade lubricant only, tools and parts accounted for, area cleaned and released by sanitation or QA before production restarts.
- Assign each task an owner and record each one when it is done.
- Review breakdowns monthly and adjust intervals where the same failure repeats.
A typical schedule
- Each shift: operator checks of guards, leaks, unusual noise and metal detector function.
- Weekly: inspect belts, chains, seals and gaskets on product contact equipment; check air compressor drains and filters.
- Monthly: lubricate on the manufacturer's chart with food-grade (NSF H1) lubricant where contact is possible; inspect motors and gear reducers; check refrigeration and cold storage temperatures against a reference thermometer.
- Quarterly or yearly: calibrate thermometers, scales and pressure gauges; service boilers, refrigeration and HVAC; replace wear parts on the hour intervals in the manual.
Records to keep
- Every work order, planned or not, with the date, asset, work done, parts and who did it.
- Calibration records for monitoring instruments.
- Hygienic release after maintenance in production areas: who checked the area and when.
- Lockout records as your energy control program requires under OSHA 1910.147.
Run it in Dovient Lite
Add each line, machine and utility as an asset, import the list from CSV or Excel if you have one, and set preventive schedules by date or by run hours with a checklist attached that includes the hygienic release steps. The work order opens when due, the tech marks each item pass, warning or fail on the phone, and the record stays on the asset. Parts such as bearings, belts and food-grade lubricant sit in the parts list with a minimum quantity and come off stock when used on a work order.
Start with Dovient LiteSources
- FDA, Sanitary operations, 21 CFR 117.35
- FDA, Equipment and utensils, 21 CFR 117.40
- OSHA, The control of hazardous energy (lockout/tagout), 29 CFR 1910.147
Rules change and vary by state and county. Check the current text with your inspector or authority having jurisdiction. Last reviewed 2026-11-15.
Questions
- Does FDA require a preventive maintenance program?
- FDA's CGMP rules require equipment and facilities to be adequately maintained and instruments to be accurate, without prescribing a specific program. A written PM program is how most plants show they meet it, and GFSI audits require one.
- What is a good maintenance schedule for a food plant?
- Operator checks each shift, weekly inspections of belts, seals and gaskets, monthly lubrication with food-grade lubricant, and quarterly or yearly calibration and utility service, with intervals from each manual.
- What is a hygienic release after maintenance?
- A check by sanitation or QA that the area is clean, tools and parts are accounted for and guards are back on before production restarts.