Grain dust housekeeping rounds each shift
OSHA's grain handling standard (1910.272) requires a written housekeeping program that sets how often dust is cleaned from floors, ledges and equipment. Put each area on a checklist (receiving pit, bucket elevator legs, hammer mill room, pellet mill floor, load-out) and the operator marks it done or failed with a photo of buildup. The round is saved with who did it and when.
Grain dust explosion prevention and OSHA 1910.272 housekeeping
Hammer mill and pellet mill PM by run hours
Give each hammer mill and pellet mill an hour meter (or a tons counter) and set intervals on it: hammers turned or replaced and screens checked every 250 hours, pellet mill die and rolls inspected every 200, main bearings greased by the manufacturer's interval. Bucket elevators, dust collectors and the boiler run on dates. The work order opens when a service is due, with its checklist attached.
Feed mill preventive maintenance and sanitation (FSMA)
Operators report problems from the mill floor
A conditioner is plugging or a bucket elevator belt sounds like it's rubbing. The operator picks the equipment in the app, describes it, adds a photo and marks it a breakdown if the line is down. Maintenance is notified, turns it into a work order, and the operator can see when it's fixed.

Hammers, screens, dies and bearings on the shelf
Keep hammer sets, screens, pellet dies, roll shells, bearings, elevator buckets and bolts, belts and dust collector bags in the parts list with a minimum quantity for each. Parts used on a work order come off stock and add to that machine's cost, and anything below its minimum is marked low stock.

Every repair in one list, with cleanout before restart
Each repair is a work order: who reported it, who is on it, photos, notes and status, with overdue work counted on the dashboard. Repairs on feed contact equipment carry a short checklist the technician or supervisor completes before restart: parts and tools removed, equipment cleaned, no metal left in the product stream. That record supports the sanitation and equipment requirements in your FSMA animal food program.
Each mill's history and cost
Every machine has one record: make, model and serial number, its run hours, its PM schedule, every work order, the hammers, screens, dies and bearings used, and what it has cost. When a pellet mill needs a new die and rolls again, you see how many hours the last set ran.
Which equipment breaks down most
The dashboard counts breakdowns and hours of downtime, shows the average time to repair (MTTR) and time between failures (MTBF), and lists the equipment that fails most often. If one leg keeps tripping on belt misalignment, the numbers show it next to the cost of each repair.
Inspection records for OSHA and FSMA
OSHA 1910.272(m) calls for regularly scheduled inspections of the mechanical and safety controls on bucket elevators, dust collectors, dryers and grain processing equipment, with a record of the date, who did it and the equipment. Completed inspections, housekeeping rounds and repairs export as a PDF for an OSHA visit, an FDA inspection or your insurer.
How setup works
- 1
Add your equipment
Import your equipment list from a spreadsheet (CSV or Excel) or add mills, elevators and dust collectors one at a time.
- 2
Set checks and intervals
Choose the checklists each area and machine needs (housekeeping rounds, elevator inspections, mill PMs) and the intervals in run hours or days.
- 3
Invite your operators and maintenance staff
They install the app and sign in. Operators see the shift's rounds; maintenance sees the repairs and PMs assigned to them.
Set up Dovient Lite with us
Tell us how many pellet mills you run. We'll go through your housekeeping rounds and PM intervals with you and set up your account.
Prefer to start on your own? Start with Dovient Lite
Feed mill checklists and guides
All templatesQuestions
What is feed mill maintenance software?
Software that keeps every machine's scheduled maintenance, inspections, repairs and parts in one record. Dovient Lite does this for small teams: housekeeping rounds and inspections on a phone, mill PMs by run hours or date, and records you can export for OSHA and FSMA.
What does OSHA 1910.272 require for housekeeping?
Section 1910.272(j) requires a written housekeeping program that sets how often and how dust is removed from ledges, floors, equipment and other exposed surfaces. At grain elevators, dust over 1/8 inch in priority areas, such as within 35 feet of inside bucket elevators, must be removed right away.
What inspection records does OSHA 1910.272 require?
Section 1910.272(m) requires regularly scheduled inspections of at least the mechanical and safety control equipment on dryers, grain stream processing equipment, dust collection equipment and bucket elevators. The employer keeps a certification record with the date, the signature of the person who did it and the equipment's serial number or other identifier. Each completed checklist in Dovient Lite records the date, the person and the asset.
What does the FSMA animal food rule require for maintenance?
The FSMA animal food rule (21 CFR 507) requires current good manufacturing practices, including equipment that is maintained and cleaned to protect animal food from contamination, and most facilities also need a written animal food safety plan. Required records must be kept for at least two years (21 CFR 507.208).
Can I issue hot work permits in Dovient Lite?
No. Dovient Lite has no permit system. You can add your hot work checks (area cleaned of dust, fire watch assigned, extinguisher on hand) as a checklist on the work order, but keep the permit OSHA 1910.272(f) requires in your permit process.
Does it alert me if a bearing runs hot?
No. Bearing temperatures checked with a handheld gun are typed into the checklist and marked pass, warning or fail. Dovient Lite doesn't send alerts and a failed item doesn't open a work order on its own; the supervisor opens one. Keep your hazard monitoring system on the elevator legs as the alarm.
Can I schedule maintenance by run hours or tons?
Yes. Each machine can have a meter for hours, tons or any other counter, and services can be set every so many units, every so many days, or whichever comes first. Readings are entered by hand or by API.
Can I track repair costs per mill?
Yes. Labor, parts and outside service charges on each work order add to that machine's cost, and each record shows its full history, so you can compare a pellet mill's die and roll spend against a rebuild.
How much does Dovient Lite cost?
Plans and prices are on the Dovient Lite pricing page: dovient.com/lite/pricing.
Reviewed
Hammer mills, pellet mills and elevators serviced by run hours


